A dealer can print out a build sheet that will show such things. Mine has almost 90,000 miles on it and not once has it let me down. This repair service applies to all 2002-2004 Super Duty vehicles gasoline and Powerstroke diesel trucks. Simply add fuel to the tank, then cycle the ignition key a few times to forward position without engaging the starter and then it should start fine, assuming that the fuel pump is functioning properly and that the fuel shut off has not been activated. And the dome light goes off after a short period too. Most are going through the driver's kick panel. First check is if the dome light comes on.
Remove plastic shield held in place with two 10 mm nuts. This can be caused by obstruction of the windshield wipers or a binding linkage. Roger It's going to be really simple to install a switch if you're going to be dealing with your cluster anyway. I went through the instrument panel to do this. When I turn the ignition switch off, the interior light comes on, the radio keeps playing, etc. Will try it out this weekend.
Since the wiper 2 relay switch contacts are normally closed to the low speed circuit of the windshield wiper motor, the motor will operate at low speed. You might have to go back further into the harness to find wire that is not discolored if this is the case. Now if some one would tell me why not spin on fuel filters? They have a clip that works similar to a clothes pin, pinch them togather and pull wires free. Do you know how to test automotive electrical circuits using a factory diagnostic test procedure flow chart? It's not like these things are going to run your battery down. I found out something I think might solve the entire problem. Check to be sure though check the rail like I explained above before removing the fuel tank!.
Low Speed Windshield Wipers Low speed is activated when the multifunction switch supplies a specific ground to the speed inputs of the windshield wiper motor module. Located right side underneath hood. Washer System The windshield washer is activated by the internal wiper motor module when it receives a ground from the multifunction switch between the washer input. Could take several times to cure the issue. They are located inside the vehicle on the cowl, behind the radio, to the right side of the throttle pedal assembly. Install the three wiper motor-to-wiper module assembly retaining bolts.
Low Speed Operation When the wiper switch is in the Low position, voltage is supplied through an internal resistor to the signal circuit. Just know - you want the Black wire with blue stripe. Once you have this installed your map and cargo light switches will still function normally. Just install a switch in that circuit and you're good to go. Also ,did you check fuse's? That wasn't even really a problem.
You can see wire color for hi and lo speed voltage. The spout is removed by removing the under column dash trim that covers the fuse panel, then removing the 7mm bolt that holds it to the dash frame. Buy correct fuel filter flex fuel vehicle uses a different filter. Just know - you want the Black wire with blue stripe. This energizes both relays and allows battery voltage from the wiper micro relay switched output to the switched input of the wiper 2 relay through its contacts and out the switched output of the wiper 2 relay to the high speed circuit of the windshield wiper motor.
Everything off, take a reading across battery posts, the generic spec for a full charge is around 12. The block heater plug should be tucked away in the front bumper. Is there anyway to eliminate this feature? I can see possibly having to reset the fuel pump inertia switch, located. The best access to the relays is from under the center of the dash, remove the heater air direction spout that's above the throttle pedal and you can see and reach them. This energizes both relays and allows battery voltage from the wiper micro relay switched output to the switched input of the wiper 2 relay through its contacts and out the switched output of the wiper 2 relay to the high speed circuit of the windshield wiper motor. It is a non-serviceable part in the instrument cluster. Install the mounting bolts and tighten to 106 in-lbs 12 Nm.
If your broke, count the miles and top off every. Once you have this installed your map and cargo light switches will still function normally. You still need to change the fluid, even though there is no dipstick. Look behind the engine, to the left, it is right next to where all your Ignition … wires plug into. Posted on Dec 13, 2010 Mike, Ford F150 relay for electric windows, position 401 in fuse box, some forums say Relay in position R02 may be tied in with pwr win. Here is the picture of the motor.
I'm not a mechanic but I don't understand why you would have to. Thank you, Grits I don't think there is any way to change that behavior, and if you remove the accessory relay then none of those accessories will work at all. We will rebuild your cluster, replacing not only the failed components, but also upgrade any components that typically fail Your instrument panel will arrive ready to install after repair. Install the mounting nut and tighten to 22-29 ft-lbs 30-40 Nm. To get to them you have to remove the bolts in the plastic wheel liner, plus the plastic pushpins. Use … of a block heater is probably not necessary unless temperatures are single digits or below. Dec 10, 2016 Did you check for voltage at the wiper fuse? This allows the furnace to fire up and warm th … e heat exchanger prior to the circulation fan coming on.
The Excursion was outsold by the Chevrolet Suburban even though the Excursion was a superior vehicle in many ways. To adjust the tension on the 7,5L engine alternator belt, loosen the adjusting bolts and rotate the alternator until the proper tension is on the drive belt and tighten the adjusting bolts. This was what was draining the battery. Since the wiper 2 relay switch contacts are normally closed to the low speed circuit of the windshield wiper motor, the motor will operate at low speed. Refer to Wiring Diagrams Cell 149 for schematic and connector information. Install the 8 plastic retainers and the 6 clips holding the cowl vent screens to the inner panels.