Popped to Halfords … and picked up a H1 bulb, went home and had a look under the bonnet. Re-fitting the headlamp is a reverse of the removal procedure, once you have located the lamp back into the car body I'd fit and tighten the screw inside the wing first, before tightening the two top screws. By depressing this loop forward towards the bumper and moving it towards the radiator, it will unlatch this loop from the tab, and allow the metal retaining clip to swing backwards and down out of the way. As simple as it sounds, the owner's manual is the best place to start for bulb replacement instructions and illustrations. I have several Ford engineer friends to whom I will make this suggestion as a replacement process. Take care not to touch the new bulb with greasy hands, use a piece of tissue to hold it.
It's not difficult to find, the head faces towards the inside of the wing. After much struggling I found that the easiest way to do this job was to remove the headlamp assembly. Open up the hood, and go in behind the fixture where the light is located. Remove the coolant reservoir one bolt and push towards the engine. Always verify all light bulb sizes, bulb voltage usage and bulb wattage before applying any information found here to your 2002 Ford Focus Sedan. Bottom Line not recommended I installed these bulbs into my 2015 Ford F-150.
There are little tabs on top of the wiring- gently i mean gently lift up on the tabs, to go over the top of the rigid locking tab the tabs are split in half so you will have to do one at a time and firmly pull on the connector rearwards. There will be a plastic cover on the back. I travel lots of unlit roads and they improve my field of vision drastically. Re-fitting the headlamp is a reverse of the removal procedure, once you have located the lamp back into the car body I'd fit and tighten the screw inside the wing first, before tightening the two top screws. Gate clip with latch on passenger side, so just push down on wire gate to release.
I don't know what I will do about the plastic clip now, the retaining wire has no tension and I'm afraid the bulb will not remain seated properly. Put the attachment ring on the new bulb, attach the wires and reverse the process. The rest is simply a reversal of these steps. Take a look at it when you get it out so that you remember which way to put it back in. That was 4 years ago and I've been using this brand ever since.
That notch is actually a tab that's cut and bent backwards towards the engine compartment. Put in new buld, be careful and try not to handle the glass on the bulb. I used a small compact mirror to enable me to see what's what. Style and performance in a single package! Push forward and then down. Check out the website www. With a pair of needle nose pliers and mirror it can be removed without force.
Use of the replacement bulb size information is at your own risk. Remove the 4 screws holding the lower tray section beneath the switch area and let it drop free. For this price, I could of paid an extra 15. Unclip and pull out the socket out. Remove four push clips for the grille, then pull gently forward to remove the grille assy. Use a tissue or something else in that order to handle the new bulb.
I had to use one hand to hold it in back and push down in the middle, while the other hand I jammed in my fingers from above so that I could get the entire cap back on. Then consult your owner's manual for the headlight bulb lamp replacement procedure. Pop the assembly back in place, attach the retaining clip and put the plastic cover back on. It's not difficult to find, the head faces towards the inside of the wing. The retainer wire is held in place on the bottom by a screw and clip on the bottom and is locked into a plastic clip on top. Like all light bulbs, headlight bulbs will eventually burn out.
The combination of our furthest downroad, more sideroad, and whiter light helps the driver achieve more clarity helping to make night driving a less stressful, more comfortable experience. With the headlamp removed, you can now replace the bulb. Remove the electric plug from the bulb to be replaced then release the wire clip holding the bulb in place and pivot it back to allow removal of the bulb. Then consult your owner's manual for the headlight bulb lamp replacement procedure. Once the bulb has been changed, you want to replace the wire the same way to protect the plastic clip.