It's fixed now though and running great. Andrew Platt: TheEbuch-I have other videos where I talk about the jet kit more. Not ridden this year Has small tear in seat taped over. Then, at least one or two more times. Don't crank them down, just until they stop. When cleaning out your tank, I'd more recommend a piece of chain or something, so when you go fishing for it later you can know for sure you've got 'all of it'. Lizard King The goal was to express his talent in art and fabrication, but besides that, Brian was motivated by his love for good old school rock.
Overall height: 1,171 mm 46. While you were in there, did you check your clearances? It goes down the road nicely. I actually thank you for not being a dick. Andrew Platt: They were cut out of stainless steel. Fresh build with less than 100 miles on it. Electric and kick start of course.
I wish you luck bud! I'll probably leave the rear shocks on for now, until I can figure out a more comfortable seat and manufacture some struts. Not ridden in 2 years, but stored in garage, not left outside at any point. Can ship for a fee. You'll have enough 'fun' getting the little crumbs and crusties of rust out. It seems to be pretty cold blooded, takes a while to warm up and will hesitate and bog until it's been running for a few minutes, is that pretty normal for this bike? Category - Engine 650 Posted Over 1 Month 1980 Yamaha xs650 Bobber Style Motorcycle Title In Hand Just Registered in July Runs Great Gets Looks Everywhere I Go New Peanut Gas Tank New paint clear coated 3 times kick and electric start ape bars new tires white wall hard tail Too much to list.
Sounds okay, but after a few years I opened it up and messed with the baffles. I'll probably cut another bike bar to fit the lever on it and attach it to the gear shifter. Seller: … New School Honda Drag Handle Bars. Could be delivered at Walneck's swap meet in Springfield, Ohio Oct. I drew up a schematic of what I wanted and he made it happen. You can also sign up for e-mail notification when such bikes are advertised in the future.
We reserve the right to re-list or sell the vehicle in the event of a non-paying bidder. The two carbs on the right side are leaking, I'm hoping it's just sticky floats. Those three easy projects will get your Honda closer to a real bobber. Considerable changes may modify oil distribution and end up in problems from that. Yes it is possible to reuse that particular gasket if it looks pliable.
Also check out our at Bikez. It has new horns better design and a new front light. Marti might have done that to his bike, but that doesn't make it safe or smart. In other words, shorten the fender rear. For the engine clean out I took apart the cylinder heads and valves to see if everthing was up to size. I live in Toronto, so with winter coming up I can either store it in my garage and let freeze to death, or go nuts with some ridiculous project! I've done some fabricating and installed some new tune-up parts. I would use anti-seize on the bolts when you put it back together, too.
The battery is toast, so I need to test the charging system. Call me at 214-943-7447 or on my cell at 817-291-9434. If you have a job and a bank account, financing is available on the year 2000 models and newer. I bought a mono shock from a Ninja 600 because the spring is rated to be used without a linkage and I'm going to try to hide the shock as best I can under the seat, sort of like this guy did on this zuk. What on earth will the next owner say! May need a minute or two with the choke on to warm up, but not long. It just takes a little nudge to take a normal, conscientious person and turn them into a paranoid, carb-cleaning maniac.
Now I don't like it. Where's a good source for carb kits and jets? Check out the videos of the bike running. I would at least get float bowl gaskets if you're taking them apart. Front and rear Disc brakes. The starter has been rebuilt and a another rebuilt starter come with the bike. It would be a good time.
The cure for that is easy and cheap, yank that cover off the airbox and use fender washers or little tabs to hold the air filter in. The bar is only 25 inches though, compared to 28-30 that are more common. The customer is responsible for registering the vehicle in their home state. I know where they live, and fully intend to get my money back, but i am doubtful. I moved them here to my home on Lake Erie where I decided to fix them up.
It seems to be pretty cold blooded, takes a while to warm up and will hesitate and bog until it's been running for a few minutes, is that pretty normal for this bike? Ross Douglas: Im working on my bike. The Story For the second time, I have been scammed by someone on Craigslist. Most drips from the light oil stopped but still watching them all closely. I think someone here was running pods but it really is almost impossible from what I've read here to get it right. I have a pretty cool idea for the rear suspension.